採用專利封裝結構與高分子材料，免除框架及玻璃，讓太陽能部署在所有結構受限的表面。
Advanced monocrystalline panels designed for corrugated roofs, curved structures, and load-limited buildings.
針對高齡廠房、承重受限、曲面結構與嚴格的法規要求，提供免鑽孔、零漏水風險的唯一解方。
The ultimate solar solution for load-limited roofs, curved structures, and strict net-zero mandates.
許多老舊鋼構廠房、大型倉庫屋頂的額外載重限額僅為 5-10 kg/m²。傳統玻璃模組（加鋼架達 15-20 kg/m²）無法通過結構安全技師認證，而 CRi 柔性組件（低於 2.7 kg/m²）可輕鬆過關。
Many older warehouse and factory roofs can only support an additional 5-10 kg/m². Standard glass panels fail weight audits; CRi modules (under 2.7 kg/m²) pass safety codes easily.
傳統安裝需在鐵皮浪板上鑽孔固定鋼骨支架，極易導致日後鏽蝕與滲水。CRi 採用氣候級高粘度結構耐候背膠直接黏貼浮貼，完全無損浪板結構與原廠防水防漏保固。
Traditional brackets require roof drilling, causing water leak risks. CRi panels are bonded flat using high-viscosity structural adhesives with zero penetrations.
台灣用電大戶條款強制契約容量大於 5000kW 企業設置 10% 綠能；歐盟 Solar Rooftop Mandate 規定 2026 起新商用建築強制安裝太陽能。輕質柔性組件是舊建物實現法規合規與 ESG 指標的最快路徑。
Taiwan's Green Energy Act mandates heavy energy consumers to install solar; EU's Rooftop Mandate enforces solar on public buildings from 2026. Flexible solar provides the fastest path to ESG compliance.
適用於移動式載具頂部、露營車及戶外應急通訊設備，實現靈活低風阻部署。
Optimized for small curves, RV rooftops, logistics trucks, and portable emergency power grids.
專為工廠波形鋼瓦、都市綠化牆體與中小溫室大棚頂部曲線貼合設計。
Designed for corrugated steel sheets, building parapets, and medium curved greenhouse arcs.
主打旗艦模組。最適於高耗能大廠屋頂、都市帷幕大牆、高樓立面及舊模組就地改裝。
Our primary commercial module. Perfect for large factories, BIPV high-rise walls, and module repowering overlays.
專為露營車頂、冷鏈物流卡車車頂、船舶及特殊載具設計的低風阻柔性板，貼附抗震防抖。
Aerodynamic low-drag flexible panels for RVs, yachts, and cold-chain truck rooftops. Vibration-resistant design.
整合高防護耐磨面料，輕量摺疊收納。內建多協議輸出接口與提把，隨開隨用。
Durable, splash-proof folding solar bag with built-in smart voltage regulator and USB/DC multi-protocol output ports.
| 比較維度Dimension | CRi 輕質柔性單晶模組CRi Lightweight Flexible Module | 傳統剛性玻璃模組Traditional Rigid Glass Module |
|---|---|---|
| 重量密度 (含鋼架)Weight Density | < 2.7 kg/㎡ (極薄貼合)< 2.7 kg/㎡ | 15 - 20 kg/㎡ (厚重偏高)15 - 20 kg/㎡ |
| 安裝工法與開孔Installation Method | 氣候級結構膠直接黏貼，免開孔不傷屋頂Direct adhesive bonding, zero roof drilling | 打孔固定重型金屬支架，具漏水生鏽風險Mechanical brackets, roof drilling required |
| 耐風能力與風壓Wind Load Resistance | 組件貼合浪板無間隙，無迎風面，抗風力強Laminated flat, zero wind uplift profile | 架高安裝迎風面大，需重型水泥壓重塊抗颱High wind sail effect, requires concrete ballast |
| 漏水風險控管Water Leakage Risk | 0 漏水風險 (不鑽孔無鑽孔老化隱憂)Zero leak risk (frameless overlay) | 高風險 (穿孔處橡膠墊片老化易導致滲漏)High risk (screw seal degradation over time) |
| 特殊表面適配度Surface Adaptability | 彎曲半徑小至 0.5m，完美契合曲面、垂直牆體Bending radius down to 0.5m, fits curves & walls | 剛硬無法彎曲，僅適用於平整無障礙表面Rigid glass structure, restricted flat setup |
| 老舊屋頂免建使照Structural Code Compliance | 極低荷重免除老舊鋼構重新建照或補強審查Light weight passes structural checks instantly | 重量過載通常要求重作結構鑑定或補強工程Heavy loads force expensive roof reinforcement |
針對運行超過 10 年、效率退化至 10-12% 的舊光電站，CRi 舊電站改造工法 不需拆卸原鋼架與舊面板。直接使用氣候膠將 560W 輕質板覆貼貼合於舊玻璃板上，省去重型施工、舊板報廢及回收清運費用，發電功率原地躍升 2 倍以上，將老舊電站轉變為高效率綠色資產。
Overlay CRi flexible solar panels directly onto degraded rigid panels. Cuts down scrap processing costs and doubles plant yield immediately.
